Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Common Terms in Rail Transport

Railcar

Any type of pre-made container designed for transportation of goods using rail locomotion. Railcars are unpowered, and require an engine to push or pull them. There are a variety of rail cars designed to accommodate a variety of shipping needs.

Engine

Powered vehicle that is operated by a pilot and is used to push or pull railcars over long distances. Engines can be electric, or powered by fossil fuels.

Full Carload

A volume of cargo that is capable of filling an entire rail car.

Less Than Carload

A volume of cargo that is less the volume required to fill an entire railcar.

Rail Yard

Railyard

A large open area alongside train tracks where trains can be domiciled or repaired. Railyards are also where cargo loading and offloading operations occur.

Heavy Haul

Train cargo that is considered bulk or full cargo, as opposed to passenger rail vehicles or light rail (usually inner city public transport).

Interchange

The act of switching cars between one train and another.

Rail Transport Arrangements

ContainerizationContainerisation – much like sea freight, many railways can accommodate containerized containerised cargo. There are no differences between the containers used in sea shipping and those use in rail shipping. The process of stuffing and sealing containers may occur at the shippers facility, or may occur at a consolidation point or forwarders facility. The same volume and weight restrictions apply to rail shipping using containerization containerisation as they do to sea shipping.

Loose Shipping – shippers may wish to ship less than full rail car loads using rail, or may not have access to intermodal container shipping through the desired rail line. Cargo can still be shipped using a variety of rail cars. Sending palletized palletised or loose cargo via rail is similar to sending cargo with a third-party trucking company – cargo will be loaded onto the train utilizing utilising pre-made and usually hard sided structures, and will be offloaded on the receiving end. Usually, shippers aren’t even allowed into the rail yard to participate in the loading/offloading of rail cars, and will only see cargo as it’s picked up outside the railyard, or once it’s delivered to their facility. Securing shipping for loose cargo via rail can be done through any freight forwarder or broker, and rail lines may even have direct customer service. 

...

Infrastructure Limitations - Rail transportation has a far limited scope compared to most other forms of cargo movement. The reality is rail movement needs specialized specialised built out infrastructure – a rail network – that requires maintenance and is easily damaged by weather or conflict. Shippers utilizing utilising rail to move cargo have very few options – the size of railcars is limited by the overall size of the tracks, and freight trains have a fairly limited set of destinations. In many contexts where many aid agencies work and operate, there will likely not be a functioning rail network all together.

...

Cargo Configuration for Rail Shipping

If not utilizing utilising intermodal shipping containers, shippers generally have very little control over how cargo is loaded, nor are there many special considerations while packaging cargo. Cargo may be shipped palletized palletised or loose, however it may be in the best interests of the shipper to palletize palletise and label cargo as much as possible to minimize minimise loss or theft while in transit. Trains can haul heavy and large cargo, and are really only limited by excessively oversized items, such as oversized construction equipment. Certain routes may be limited by tunnels or underpasses, so shippers should inquire with their forwarders about the overall limitation for shipping using a specific rail line.

The overall types of railcars used for shipping are:

Image RemovedImage Added

Box Car – The most common form of pre-made purpose built rail car. Box cars are sealed on all sides and have hard, rigid structures with locking doors. Box cars need to be manually loaded, similar to the bed of a box truck.

Image RemovedImage Added

Flat Car – A car without hard siding, used to transport wide or tall cargo such as vehicles and construction equipment. Flat cars can also house standard shipping containers. Flat cars can also be used for regular cargo, but would expose regular cargo more to the elements and theft.

Image RemovedImage Added

Hopper Car – An open top box car with reinforced support under the long edges. Hopper cars are used for hauling large quantities of loose bulk items, such as grain, sand, ore, or anything non liquid that can be dumped directly into the body of the car. Offloading may be done by hand or MHE. Some hopper cars are capable of tilting to rapidly offload bulk cargo at once.

Image RemovedImage Added

Tank Car – Can be low-pressure (liquid) or high-pressure (gas). Ideal for moving large volumes of liquid long distances. There may be restrictions on the liquid and gas types due to national and local laws and limitations on handling hazardous goods

...

Under very specific circumstances, barges can be an extremely cost-effective way of moving large volumes of cargo relatively large distances.  Barges are wide, flat river vessels with low edges, have flat bottoms, and have a shallow draft. This makes barges ideal for use in calm flat and shallow waters like a river, but largely unsuitable for turbulent waters like the open ocean. Barges can come in two configurations:

Image Modified

Self-propelled – Self-propelled barges have a connected cabin and engine mount, and move as a single piece. Usually the engine is designed for moving large loads, but isn’t meant for speed.

Image Modified

Dumb Barges – A “dumb” barge is an non self-powered floating platform, capable of holding cargo, but is without steering or an engine. Dumb barges require an external boat to move, including a tow boat or a “pusher,” a separate motivated boat that is specifically designed to push or pull dumb barges along waterways.

The barges themselves are divided into two general categories:

Image Modified

Flat Deck – A barge on which the deck stowage is one large flat surface, upon which cargo rests and is secured to. Flat deck surfaces on barges are very exposed - they won't protect cargo from waves or from turbulent water, and items stored on the surface of flat decks can be easy targets for thieves. All cargo transported on the surface must be properly secured and tied down, and valuable items stored in a manner that won't enable easy theft. 

Image Modified

Hopper / Split Hopper – A barge with one large or many smaller compartments that are partially below the edge of the barge. Hoppers can be used to store bulk loose items such as grains, sand or ore. Many hoppers can be covered with tarp or hard metal lids to protect contents, and some can even store additional cargo on top of the hopper compartments. Depending on the cargo, hopper/split barges can be loaded by hand or

specialized

specialised MHE. 

Image Modified

Tanker Barge - A barge designed to carry liquids or compressed gasses. Tanker barges requires

specialized

specialised maintenance, and will only be used if the sending and receiving ports have the proper equipment to load and offload. 


Barge movement is likely the cheapest mode of moving cargo inland into a country, however it has limitations. Barging operations are extremely slow; the loading and offloading process can take days or weeks depending on the load type and the journey itself can take weeks to accomplish. Barges are also further limited by the ability to safely moor and offload at the point of delivery. Barges themselves can be impacted by seasonal changes to the riverway, making areas impassable for periods of time.

In reality, there are only a few locations globally where barges will be effectively used in a humanitarian response operations. There is no standard form of documentation for utilizing utilising barges, and users of barge services will need to supply their own tracking documentation and process their own customs formalities if required to.

...

There may also be large riverway shipping operations on vessels capable of carrying relatively large volumes of cargo. Utilizing Utilising third-party riverway shipping should be treated the same as utilizing utilising any local third-party transport.

...

Any goods being moved via animal must be packaged in relation to the weight that the particular animal can safely and humanely carry. There are many possible variations of available local animals depending on geography, climate, the local economy, and a variety of other local conditions. 

A general guide to working limitations of different pack animals might look like:

Animal

Load Capacity

Daily Work Rate

Region

Elephant

500 kg

5-8 hours/walk 24 km

Asia

Donkey

50 kg

Mountain, 8 hours

Middle East, Africa, South Asia, Latin America & Caribbean

Mule

50 kg

Mountain, 8 hours

Middle East, Africa, South Asia, Latin America & Caribbean

Llama

50-80 kg

8-10 hours/walk 30 km

South America

Horse

60 kg

6 hours

Asia, Eastern Europe, Middle East & North Africa

Bull

150-250 kg

8-10 hours

Middle East & North Africa, South Asia

Camel

150-250 kg

Walk 50 km

Middle East & North Africa, South Asia

Yak

70 kgs


South Asia

Pack animals estimated their work rates - WFP Transport and Logistics Manual 

Speaking with a local expert is strongly advised when developing an animal delivery plan. Typically, use of pack animals will be negotiated and contracted directly with the owners, or those in control of the animals who will be responsible for the transport. These may include:

  • Village elders.
  • Local authorities.
  • Committees of animal owners.
  • Local NGOs.

Transport documents will vary, but a variation of the standard method may be used, possibly amended as follows:

  • Issue one waybill for each group.
  • Divide the animals into groups of under one supervisor.
  • List animal owners and number of animals provided by each individual.
  • Assign a quantity of consignment to each group, for accountability.

All contracts for carriage by pack animals should still undergo the standard procurement process established by each individual agency, and and be within each agencies procurement procedures.